Skip to main content

Flash memory chip built out of single-atom-thick components

Graphene, a single-atom thick sheet of carbon, has become the focus of a lot of research (and a Nobel Prize) because it has some interesting electronic properties: electrons move through the material as if they have no mass. But it's only one of a number of single-atom thick materials that have been discovered, and some of the others have very different properties, acting as semiconductors or insulators.
The discoveries raise the prospect of building more complex electronic devices out of a series of these materials, with each part being only a single atom thick. Now, researchers have used two of these materials—graphene and molybdenum disulfide—and put them together with some more traditional components to make a flash memory device. Although the work is very preliminary, with some of the parts being assembled by hand under a microscope, it shows some excellent properties, like the potential to store more than one bit per device and the ability to retain its state for over a decade.
The basic outline of a flash memory device involves two electrodes that feed current through a semiconductor within the device. When a negative voltage is sent across a device from a control electrode, electrons are able to feed into a reservoir that retains the charge; reversing the voltage allows them to escape. The presence of the electrons in the reservoir can be read out by sending current through the semiconductor.
To build a compact version of the device, the authors of the new paper (who are based in Lausanne,
Switzerland) started with two sheets of graphene layered on some silicon, separated by a small gap. These served as the electrodes, with the device itself acting as a bridge between them. The next layer on top of that was the semiconductor, formed by a single-molecule-thick sheet of molybdenum disulfide. Above that, a layer of an insulator that allows electrons to tunnel through it separated the conductor from the charge reservoir. To hold the charges, the authors used a few layers of graphene. That was topped by a bit more insulator and another electrode that acted to control the device, setting it to read or erase.
The insulator used in this work wasn't a single atom thick (although insulators of this sort are known) and the graphene charge reservoir was several layers thick, so there were clearly a number of layers involved. But still, this is a very thin device, and can potentially be made even thinner. The manufacturing technique could use some improvements as well, given that one of the steps involved finding individual layers using an optical microscope. 
In any case, the devices worked. Applying a positive voltage to the control electrode allowed charge to accumulate in the graphene layers, and its presence could be read out based on the current flowing through the device. Reversing the voltage across the control electrode erased the device. They went through 120 write/erase cycles, and the device still functioned. They also left the device unpowered for a bit, and found that while its storage did decay a bit, it only decayed very slowly. Based on the rate, they expect that, after 10 years, 30 percent of the original charge would still be present.
The difference in current between the clear and charged state was also very large, with the ratio between the current flowing in them being 104. That should allow a single device to encode a number of distinct states, meaning it can store multiple bits, a technique already in use in multilevel flash memory.
Like graphene, molybdenum disulfide is flexible, meaning that it could potential find uses in some non-traditional electronics. And the authors seem confident that devices based on it can be mass produced with techniques that are already established. Still, it's clear that there are a number of issues to be worked out before this is ready for the factory floor.

 

Comments

Popular posts from this blog

LG’s first flexible OLED phone due before the year is out

LG plans to launch a flexible OLED smartphone before the end of the year, the company’s VP of mobile has confirmed, though it’s unclear to what extent the work-in-progress handset will actually flex. The OLED panel in question is the handiwork of LG Display according to VP of LG mobile Yoon Bu-hyun, the WSJ  reports, with the proposed device set to launch sometime in Q4. LG Display’s work on flexible OLEDs has been underway for some time, though the company’s efforts have perhaps been overshadowed somewhat by rival Samsung’s YOUM development. Last year, according to a Korea Times report, LG Display was preparing for
Flexible displays are the Future of IT Industry! A part from 4k and smart home appliances, the CES 2013 saw a lot of attention being drawn towards bendable, flexible displays. The elasticised display idea isn’t something new as we have seen hoards of device concepts being crafted around flexible, bendable and even foldable displays. These concept devices give us a futuristic feel, be it a flexible phone to be worn around the wrist or a phone that opens up to turn into a tablet or PSP-like device. But how far is this future? Nokia has been toying with the idea ever since we remember. The technology sounds very fascinating and the possibilities and the extent to which bendable displays could be used are vast and leave us spellbound. However, these have always been concepts and we haven’t seen any device materialise in the real world. There have been several technologies that were conceived in these years and all have been put to their practical use. But the bendable d

Xarius: Charge Your Mobile From Air

Xarius is a portable energy generator that allows to charge electrical appliances by the use of windpower in areas without electricity. Its lightweight and compact design makes the wind turbine to a perfect companion on backpacking trips with little luggage. It is composed of a foldable three-wing-system and an internal energy generator. The integrated rope makes it easy to adapt to any environment.Hooks are attached to both of its ends to tighten the rope and open the wings at the same time using the resulting tension. For convenient charging the battery is permanently installed, so that the electrical device can be charged inside the tent. The LED on the hook shows the current charge of battery. The pulsating orange indicates that the wind turbine has to recharge. Even at low wind speeds the blades begin to rotate autonomously.